For 23€, the support is really well made! does not give a cheap effect to the touch at all, but a robust effect, the DJI's outfit is good, loving and powerful. Very good value for money, I recommend!

The part is more fun than expected. On the one hand, because it is very well made and fits perfectly, it also adds little size and weight to the Osmo, and on the other hand due to the unexpected creativity bonus. Because once you have the part on, you immediately look everywhere for ways to install the camera. This results in interesting new angles and perspectives time and again. It is quick to install, it is also nice that a handle for the wrist strap has been thought of, and when the flap is closed, the part is bomb-proof. The magnetic stand can be adjusted in angle and also holds reliably. You can't ask for more. Some protection for the case, buttons and joystick is a welcome side effect. And actually, you can simply leave the part on, because it doesn't interfere with handling much, especially if you have installed an extension and pass the gimbal over it.

This is a nice accessory for the Osmo Pocket 3.It is perfect for the solo traveller.The magnet is strong and sticks well.It has a clip on the side to place the pocket in it. It is strong and has very less chances of opening.Since the magnet opens, it does increase the length and makes it a little easier to hold the pocket.It came with the hex key to tight the screw.The mount itself has some weight, but it doesn't make the pocket 3 heavy.I would definitely recommend it.

This is a well made stand and fits the pocket 3 like a glove while still giving access to the buttons.Magnets are strong and hold fast to flat surfaces.

Great fit, great strength. make sure the metal surface is the same size

I have to admit that I acted very stupid in the first few minutes to fit my camera in this housing. Once you understand it, it's easy and done in ten seconds. The camera fits perfectly and you can place it on any metal surface. As long as it's not too dirty, you should say so. There are no limits to creativity. The cage can be tilted in various ways or the entire housing can be rotated. This is one of the small tools that make Pocket 3 so versatile. I'm going to travel to Japan in two days and will definitely take this handy helper with me. Great.

The K&F Concept magnetic stand for the DJI Osmo Pocket 3 offers a flexible solution for mounting the camera both on tables and on vertical surfaces. With 180° adjustability, it enables versatile shooting angles and positions. Positive:

It has a grip that I didn't expect!!!

The Pocket 3 stand with magnetic holder from K&F comes in attractive packaging and contains, in addition to the holder itself, an Allen wrench and short instructions. The mount is mostly made of plastic, but it looks sturdy. To attach the Pocket 3, I open the front flap of the holder, insert the camera and close it again so that the device is securely fixed. The joint can be individually adjusted using the included Allen wrench — tight enough to hold the camera in position, yet flexible enough to be able to adjust the angle without having to tighten again. The magnets do a good job on all flat metal surfaces and enable reliable attachment. However, they reach the limits of usability on curved or very narrow surfaces. In addition, the mount can be used as a simple stand as long as the surface is flat enough. However, as the 3.5 cm base is quite narrow, care should be taken — side shocks can cause the camera to tip over. Overall, the K&F magnetic holder impresses me. It opens up new opportunities for shooting from unusual perspectives and is a useful addition for creative videographers. It shows its strengths particularly in controlled environments, such as in the gym. Since I've been using them, the quality of my recordings has been noticeable - an extremely practical accessory that I am happy to recommend with 5 stars.

I had the opportunity to try the K&F Concept magnetic mount for the DJI Osmo Pocket 3 and I must say that it is an extremely practical solution for those looking for a versatile way to fix the camera. The idea of being able to mount it on metal surfaces is really functional, and the support manages to keep the Pocket 3 firm without vibrations, even during moving shots. The construction quality is excellent: although the main material is plastic, it is sturdy and light. The feature that struck me the most is the ability to adjust the angle up to 180° in a simple and fast way, without the need for tools. I mounted it on a flat metal, and the magnet held up perfectly, even with the weight of the Pocket 3. The base is non-slip and offers good stability, but be careful to place it on tight or curved surfaces, where the magnet may not be as effective. The use as a desk support is very comfortable, while outside you have to be careful where it sticks, since more irregular surfaces may not guarantee the same tightness