How To Change Ring Doorbell Camera Battery ?

To change the battery of a Ring Doorbell camera, follow these steps:

1. Remove the faceplate: Gently press the release tab at the bottom of the doorbell and slide the faceplate upwards to detach it from the device.

2. Disconnect the battery: Locate the battery compartment on the back of the doorbell. Press the release tab and pull the battery out to disconnect it from the device.

3. Replace the battery: Insert the new battery into the compartment, ensuring it is properly aligned. Push it in until it clicks into place.

4. Reattach the faceplate: Align the faceplate with the front of the doorbell and slide it downwards until it snaps back into position.

5. Charge the battery: If the new battery is not fully charged, you can connect the doorbell to a power source using the provided USB cable to charge it.

6. Test the doorbell: Once the battery is installed and charged, test the doorbell to ensure it is functioning properly.

Note: The specific steps may vary depending on the model of your Ring Doorbell camera. It is recommended to refer to the user manual or Ring's official website for detailed instructions.

1、 Removing the Ring Doorbell Camera from its mounting bracket

To change the battery of your Ring Doorbell Camera, you will need to remove it from its mounting bracket. Here's a step-by-step guide on how to do it:

1. Start by turning off the power to your Ring Doorbell Camera. Locate the circuit breaker that controls the power to the doorbell and switch it off. This is an important safety precaution.

2. Once the power is off, locate the security screw at the bottom of the doorbell. Use the provided screwdriver or a small Phillips head screwdriver to remove the screw.

3. After removing the security screw, you can now slide the Ring Doorbell Camera up and off the mounting bracket. Be careful not to pull too hard, as there may be wires connected to the back of the device.

4. Once the doorbell is removed, you will see the battery compartment on the back. Open the compartment by sliding the latch or pressing the release button, depending on the model of your Ring Doorbell Camera.

5. Take out the old battery and replace it with a fully charged one. Make sure to use the correct battery type specified by Ring.

6. Close the battery compartment and slide the Ring Doorbell Camera back onto the mounting bracket. Align the screw holes and insert the security screw to secure the device in place.

7. Finally, turn the power back on at the circuit breaker to restore power to your Ring Doorbell Camera.

It's worth noting that Ring Doorbell Cameras have different models and designs, so the exact steps may vary slightly. Always refer to the user manual or Ring's official website for specific instructions for your device.

2、 Opening the battery compartment on the back of the camera

To change the battery on your Ring Doorbell camera, follow these steps:

1. Ensure that your Ring Doorbell camera is disconnected from any power source. This includes removing it from its mounting bracket if necessary.

2. Locate the battery compartment on the back of the camera. The battery compartment is typically located at the bottom of the device.

3. Gently press the release button or slide the latch to open the battery compartment. The exact method may vary depending on the model of your Ring Doorbell camera.

4. Once the battery compartment is open, carefully remove the old battery from the camera. Take note of the battery's orientation, as you will need to insert the new battery in the same way.

5. Insert the new battery into the compartment, ensuring that it is properly aligned with the contacts. Push the battery in until it clicks into place.

6. Close the battery compartment by pressing it shut or sliding the latch back into place. Make sure it is securely closed to prevent any water or dust from entering.

7. Reconnect your Ring Doorbell camera to its power source or remount it on its bracket.

It's important to note that the process of changing the battery may vary slightly depending on the specific model of your Ring Doorbell camera. Therefore, it's always a good idea to consult the user manual or visit the Ring website for detailed instructions specific to your device.

Additionally, Ring Doorbell cameras now offer the option of using a removable, rechargeable battery pack or connecting to existing doorbell wiring for continuous power. This provides users with more flexibility and convenience when it comes to powering their devices.

3、 Removing the old battery from the compartment

To change the battery of your Ring Doorbell camera, follow these steps:

1. Start by removing the old battery from the compartment. Depending on the model of your Ring Doorbell, the battery compartment may be located on the front or back of the device. Look for a small latch or release button near the bottom of the doorbell.

2. Once you locate the latch or release button, press it and gently slide the battery compartment cover off. Be careful not to force it or use excessive pressure, as this could damage the device.

3. Inside the compartment, you will find the old battery. Carefully lift it out and set it aside. It's important to handle the battery with care and avoid touching the metal contacts on the bottom, as this could interfere with its performance.

4. Before inserting the new battery, take a moment to clean the battery compartment with a soft, dry cloth. This will help ensure a good connection between the battery and the device.

5. Now, insert the new battery into the compartment, making sure the metal contacts on the bottom of the battery align with the corresponding contacts in the compartment. Gently press the battery down until it is securely in place.

6. Finally, slide the battery compartment cover back onto the device until it clicks into place. Ensure that it is properly sealed to protect the battery from moisture and other elements.

It's worth noting that the process of changing the battery may vary slightly depending on the specific model of your Ring Doorbell camera. Therefore, it's always a good idea to consult the user manual or visit the Ring website for detailed instructions specific to your device.

4、 Inserting a new battery into the compartment

To change the battery of your Ring Doorbell camera, follow these steps:

1. Remove the faceplate: Gently press the release button located at the bottom of the doorbell and slide the faceplate upwards to detach it from the device.

2. Access the battery compartment: Once the faceplate is removed, you will see the battery compartment. It is usually located on the right-hand side of the device.

3. Remove the old battery: Depending on the model, you may need to unscrew the battery compartment cover or simply pull it open. Take out the old battery from the compartment.

4. Insert the new battery: Take your new battery and carefully insert it into the compartment. Ensure that the positive and negative terminals of the battery align with the corresponding markings inside the compartment.

5. Close the battery compartment: If there is a cover, screw it back into place or close it securely. Make sure it is tightly sealed to prevent any water or dust from entering.

6. Reattach the faceplate: Slide the faceplate back onto the device until it clicks into place. Ensure that it is properly aligned and flush with the doorbell.

7. Test the battery: Once the battery is inserted and the faceplate is reattached, check if the doorbell powers on and functions properly. If not, double-check the battery installation and contact Ring support if needed.

It is important to note that the specific steps may vary slightly depending on the model of your Ring Doorbell camera. Therefore, it is always recommended to refer to the user manual or Ring's official website for detailed instructions specific to your device.

As technology advances, Ring may introduce new models with different battery replacement methods. Therefore, it is advisable to stay updated with the latest information provided by Ring to ensure a smooth battery replacement process.